Page 394 - Catalogue-Osawa-2021

HF UNI - Variable Helix and unequal pitch - 45° chamfer

CUTTING PARAMETERS
INFO
HF444

Material Group P1 P2 P7 K1 P3 P4 M1 K2 K3 P5 M2 M3 K4 S1 S4 S2 S3 S5
ISO 513
Hardness/Rm ≤700 N/mm² 600÷1000 N/mm² ≤35 HRC ≤40 HRC
ap x ae D x 0.4D D x 0.4D D x 0.25D D x 0.25D
Vc (m/min) 100÷120 60÷80 45÷65 30÷40
CARBIDE D fz fz fz fz
DRILLS
(mm) (mm/z) (mm/z) (mm/z) (mm/z)
VERTICAL
6 0.026 0.024 0.020 0.018
PU-HPU
8 0.034 0.031 0.026 0.024
TA-4HTA
10 0.041 0.037 0.031 0.029
SUH
ALH 12 0.047 0.042 0.035 0.033
HRC 14 0.052 0.047 0.039 0.037
SUH MINI 16 0.058 0.052 0.044 0.041
HL 20 0.071 0.064 0.053 0.050
HSD
C-SD-TA
Material Group P1 P2 P7 K1 P3 P4 M1 K2 K3 P5 M2 M3 K4 S1 S4 S2 S3 S5
ISO 513
Hardness/Rm ≤700 N/mm² 600÷1000 N/mm² ≤35 HRC ≤40 HRC
ap x ae 2D x 0.2D 2D x 0.1D 1.5D x 0.1D 1.5D x 0.1D
Vc (m/min) 160÷200 110÷130 80÷100 50÷70
D fz fz fz fz
(mm) (mm/z) (mm/z) (mm/z) (mm/z)
TROCHOIDAL
HSS 6 0.066 0.059 0.052 0.072
DRILLS
8 0.085 0.077 0.068 0.094
10 0.102 0.092 0.082 0.112
LFTA
12 0.117 0.105 0.093 0.128
SUTA
14 0.131 0.118 0.105 0.144
HSS-HSS/CO
16 0.146 0.131 0.117 0.160
20 0.177 0.160 0.142 0.195
NOTES:
Down milling CNC programming is required.
“ae” value max 0.2xD - “T” value max 0.1xD.
The use of end mill with diameter 30-40% smaller than the width of the slot is recommended.
The cutting conditions are based on CNC programming with medium dynamic speed.
CARBIDE With lower CNC dynamic speed, use the same cutting conditions or reduce the cutting speed Vc.
END-MILLS With higher CNC dynamic speed, reduce the “T” value by approximately -30 -50% and apply the maximum available cutting speed Vc.
G2 ae R1 Cutter radius
MDTA R2 Half of slot width
HF VH/UP T Programming width of cut
MEF R2 ae Actual width of cut
ALU R1

MEX/MH
UH/MH
Y (+)
Y

X (+)
T

HSS
END-MILLS

CARBIDE
BURRS

PARAMETERS SUGGESTED WITH HIGH POWER MILLING CHUCK AND STABLE MACHINING CONDITION
392

21/10/2021 12:13:44
Libro 1.indb 392
Libro 1.indb 392 21/10/2021 12:13:44